Lancia Beta Forum

Technical stuff => Fuel System Carb => Topic started by: Neil-yaj396 on August 24, 2021, 12:08:10 PM



Title: Fuel Hose
Post by: Neil-yaj396 on August 24, 2021, 12:08:10 PM
What size flexible hose are folks using? A search threw up reference to 5mm (bore) for the return pipe which seems a bit big to me, although I'm not convinced that the smaller pipe that I fitted recently (3mm?) is delivering sufficient flow. It is the mechanical pump to carb hose that I need to replace now.

I also seem to be bedeviled by the fitting clips not giving sufficient clamping, so any recommendations for those would also be welcome.


Title: Re: Fuel Hose
Post by: Neil-yaj396 on August 24, 2021, 01:09:29 PM
Further browsing revealed that I asked this question in 2011 when I was replacing the hoses on YAJ!

8mm & 6mm were suggested, but I still think these are on the large side for my car in both instances.


Title: Re: Fuel Hose
Post by: JohnFol on August 24, 2021, 05:16:53 PM
When I fitted an electric fuel pump I used this stuff

https://www.amazon.co.uk/gp/product/B00XU8M2SM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 (https://www.amazon.co.uk/gp/product/B00XU8M2SM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1)

Interestingly ID is 8mm and you are concerned 5mm might be too big..


Title: Re: Fuel Hose
Post by: Nigel on August 24, 2021, 10:10:23 PM
Hi Neil,

I used the full circumference clamp, I think from Car Builder, with the 3-4 mm screw.
Don't use jubilee type if you can avoid it.

These days hoses need to be ethanol-proof, and I don't read a mention of that in the
type that John got. I don't know the numbers to look out for though.

Nigel


Title: Re: Fuel Hose
Post by: peteracs on August 24, 2021, 11:16:41 PM
Hi All

I believe the recommended fuel hose are to R9 spec. I bought Coline branded hose for mine. It is recommended you buy a definite recognised brand as there are reported to be a older R6 hoses which have been relabelled and are not so tolerant of the latest ethanol mix.

This website gives you a wordy, but informative view on fuel hoses.

http://www.volksbolts.com/faq/fuelhose.htm (http://www.volksbolts.com/faq/fuelhose.htm)

Peter


Title: Re: Fuel Hose
Post by: Neil-yaj396 on August 25, 2021, 07:57:11 AM
When I fitted an electric fuel pump I used this stuff

https://www.amazon.co.uk/gp/product/B00XU8M2SM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 (https://www.amazon.co.uk/gp/product/B00XU8M2SM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1)

Interestingly ID is 8mm and you are concerned 5mm might be too big..

Thanks John, 5mm is for the return, not the main pipe. Good suggestions from all on spec, but I'm still unclear on the bore sizes being used?


Title: Re: Fuel Hose
Post by: smithymc on August 25, 2021, 08:59:04 AM
I used Codan ethanol safe stuff. Its marked 7.9mm or 5/16” id.

Mark



Title: Re: Fuel Hose
Post by: JohnFol on August 25, 2021, 10:14:57 AM
Hi Nigel, it's not clear so I re-read the description of what I bought and cross referenced a few sites.
"SAE J30 R6 grade hosing for ethanol enriched E5 and E10 petrol."

So I think I'm ok


Title: Re: Fuel Hose
Post by: peteracs on August 26, 2021, 06:24:48 PM
Hi John

If the article I ref’d above is to be believed, the R6 standard was introduced way before the newer ethanol fuels were and there is a chart showing the relative permeability of R6 and R9 which is a 400:15 difference ie 26 times more permeable to modern fuels. That is not to say it is not safe, just if you have R6, keep a regular eye on it for weeping. If in doubt replace it of course.

Peter


Title: Re: Fuel Hose
Post by: mangocrazy on August 26, 2021, 10:55:01 PM
I did some research on this a few years ago and concluded that the fuel hose that's readily available in the UK is mainly not fit for purpose. If you look at the fuel hose available in the USA, where they have had ethanol in their petrol for far longer and at much higher concentrations, their fuel hose is way ahead of what we can routinely buy. Seven or eight years ago I obtained some Gates Barricade Greenshield hose, which had vanishingly low levels of permeability and was warranted safe against ethanol (all concentrations), methanol and heaven knows what else. Whereas we can buy fuel hose that conforms to R6 or R9 of the SAE J30 standard, Gates Barricade hose conforms to  R14 (T1), and has done for many years.

Thankfully it seems like this hose is now becoming available in the UK, if you look carefully, so if you can track any of it down I'd use it in preference to any other hose.


Title: Re: Fuel Hose
Post by: JohnFol on August 26, 2021, 11:49:07 PM
Beaulieu auto jumble is only a week away...


Title: Re: Fuel Hose
Post by: Neil-yaj396 on September 25, 2021, 07:55:01 AM
Following this thread through can someone recommend a good pair of pipe cutters? I've used a serrated knife or junior hacksaw in the past but the new pipes that I've bought, and I'm taking this as a good sign, are noticeably tougher.

As I'm changing all the flexible pipes, front and back, I've plenty of cutting to do.


Title: Re: Fuel Hose
Post by: peteracs on September 25, 2021, 08:11:35 AM
Hi Neil

I just use Stanley type knife.

Peter


Title: Re: Fuel Hose
Post by: WestonE on September 25, 2021, 10:14:01 AM
Hi Neil

Avoid using a saw it can drop rubber crumbs into the pipe that end up blocking jets. A stanley or decent snap off blade knife works. Just make sure you keep using a SHARP blade.


Eric 


Title: Re: Fuel Hose
Post by: mtulloch on September 27, 2021, 10:28:31 PM
I use cable cutters like this

https://www.zoro.co.uk/shop/hand-tools/insulated-tools---pliers-and-cutters/00125-9%22-cable-cutter/p/ZT1199157X?utm_source=bing&utm_medium=shopping&utm_campaign=bs%2B%7C%2BHand%20Tools&utm_term=ZT1199157X&dev=c&utm_campaign=bs%20-%20hand%20tools%20%230&utm_medium=shopping&msclkid=7ca991c5361b1bd0c1ddf097013832ce&utm_source=bing&utm_prodid=ZT1199157Xtargetid (https://www.zoro.co.uk/shop/hand-tools/insulated-tools---pliers-and-cutters/00125-9%22-cable-cutter/p/ZT1199157X?utm_source=bing&utm_medium=shopping&utm_campaign=bs%2B%7C%2BHand%20Tools&utm_term=ZT1199157X&dev=c&utm_campaign=bs%20-%20hand%20tools%20%230&utm_medium=shopping&msclkid=7ca991c5361b1bd0c1ddf097013832ce&utm_source=bing&utm_prodid=ZT1199157Xtargetid)


Title: Re: Fuel Hose
Post by: Sandro on September 30, 2021, 08:56:28 AM

While we're on the topic has anyone used or heard of Alfagomma fuel hoses ?

They're in stock at the local Auto parts place I purchase from and I wondered if anyone here has had any experience good or otherwise using this brand.
I've written to Alfagomma in the meantime to try to glean some more specific product information.

Thanks,

Andrew

   


Title: Re: Fuel Hose
Post by: mangocrazy on September 30, 2021, 10:22:28 PM
I think the very first question you should ask of any fuel hose vendor is 'what level of the SAE J30 specification does your hose conform to?'. The latest and highest level is (I believe) R14 T1. Anything less than this should elicit further questioning.


Title: Re: Fuel Hose
Post by: peteracs on October 01, 2021, 12:25:02 PM
Hi Graham

I have read some threads on R14 just to confuse where it is rated at a lower PSI than R9, so folk were less inclined to use for that application. It is mentioned here that R9 is for high pressure use, R14 is for low pressure.

http://www.volksbolts.com/faq/fuelhose.htm (http://www.volksbolts.com/faq/fuelhose.htm)

I have no way of confirming this, but mentioned on more than one site.

Peter


Title: Re: Fuel Hose
Post by: mangocrazy on October 01, 2021, 05:07:27 PM
I wasn't aware of R14 being for low pressure use, but will check further. For carburetted cars that wouldn't be a problem, as max fuel pressure is of necessity very low. The Gates Barricade Greenshield hose for fuel-injected cars is safe up to 16 bar (235 psi). The hose sold for carb engines is safe up to 2.4 bar (35 psi). Both hose types are certified compliant with the SAE J30 R14 standard.

From what I can see, SAE J30 R14 T1 is for low-pressure hose with ultra-low permeability. The 16 bar Gates hose I referred to above is actually listed as SAE J30 R14 T2, so I suspect there are sub-types depending on whether low or high pressure use is required. The main point about R14 is that it is the standard for ultra-low permeation properties. This type of hose is typically approved for use with leaded and unleaded petrol, diesel, biodiesel, E85, methanol, ethanol and gasohol fuels.

So providing you match the hose type (T1 or T2) to the intended pressure application, I'd say go with R14 every time due to its exceptionally low permeability.


Title: Re: Fuel Hose
Post by: peteracs on October 01, 2021, 07:22:45 PM
Hi Graham

There was some mention of the R14 spec being related to low emissions requirement and not seen anything on type 2, so good call on differentiating the two types, good job it is only complicated. From what I can see R9 is also ok to use on ethanol, but not necessarily on some other fuels.

Peter


Title: Re: Fuel Hose
Post by: Sandro on October 04, 2021, 07:54:54 AM
Thanks everyone.

Andrew.


Title: Re: Fuel Hose
Post by: Neil-yaj396 on October 04, 2021, 11:18:00 AM
Filter King now fitted and plumbed to my mechanical pump with new hose.

The Silverline cutting tool was a very reasonable price and cuts fuel hose really well.

Hopefully the refurbished carburetor will be back in the next couple of weeks.


Title: Re: Fuel Hose
Post by: alcarr on October 04, 2021, 09:00:48 PM
Hello Neil
Can you tell me which company you used to refurbish your carburettor. I’m not at the stage to do this, but I would be interested in hearing your thoughts on the result.

Regards Alan


Title: Re: Fuel Hose
Post by: Neil-yaj396 on October 05, 2021, 08:17:46 AM
Hello Neil
Can you tell me which company you used to refurbish your carburettor. I’m not at the stage to do this, but I would be interested in hearing your thoughts on the result.

Regards Alan

Alan

I've used CFS in Bradford, they advertise in the back of Practical Classics. I'll post how I get on once the carb is back on and working.

Neil


Title: Re: Fuel Hose
Post by: alcarr on October 07, 2021, 10:56:25 PM
Hello Neil
I saw the advert in Practical Classics, I noticed that there are several companies that do carburettor refurbishment, have you used this particular one before?
Regards Alan


Title: Re: Fuel Hose
Post by: Neil-yaj396 on October 08, 2021, 08:54:29 AM
No, they are new to me but they have advertised for several years. I mainly opted for them as they are local, so no transit risks.


Title: Re: Fuel Hose
Post by: A1.6HPE on October 11, 2021, 05:58:48 PM
I'm a bit late joining this conversation, but:

On my carburettor equipped HPE the hose connection tubes on the carburettor and the tank measure just over 8mm for the feed and just over 6mm for the return. To me that defines the size of flexible hoses required.  The tube ends are belled to provide a snug fit for the flexible hoses.
Not measured the pump connections.

Leo


Title: Re: Fuel Hose
Post by: Neil-yaj396 on March 15, 2022, 02:27:10 PM
I finally got to run the car with the refurbished carb and the Filter King for half an hour in mixed driving conditions; queueing traffic through to 70mph on a dual carriageway. At first there was a fairly bad flat spot/hesitation when pulling away, but I'm putting that down to a fouled spark plug, as this cleared completely after about 15 minutes. After that, super smooth and pulling away strongly in all gears.

Just the brakes to sort now before hopefully attending a summer of top events......


Title: Re: Fuel Hose
Post by: Neil-yaj396 on August 20, 2022, 08:43:31 AM
With a week to go before my drive down to Goodwood I finished the nearly year long upgrade to the fuel system by changing the rear flexible pipes. Definitely past their best. It's the first bit of what I would call proper spannering since my illness and I'm aching all over this morning....


Title: Re: Fuel Hose
Post by: Neil-yaj396 on August 20, 2022, 08:44:09 AM
.....


Title: Re: Fuel Hose
Post by: JohnFol on August 20, 2022, 12:16:13 PM
Neil, the price list link on Classic Fuel System's Web site is broken. Would you mind sharing how much they charge? Also interested if they set float levels, idle speed, mixture etc as part of the service


Title: Re: Fuel Hose
Post by: Neil-yaj396 on August 21, 2022, 08:57:25 AM
Neil, the price list link on Classic Fuel System's Web site is broken. Would you mind sharing how much they charge? Also interested if they set float levels, idle speed, mixture etc as part of the service

The full rebuild was £145. Everything was ready to go except the idle speed that I set as per Capriblu's instructions (link below). I'm planning a bigger test drive on Tuesday but so far I'm amazed at the steady idle throughout the warm up and the tractable power delivery that the rebuild plus the addition of the Filter King has delivered.

If you do use CFS don't be put off by it being and old guy in his especially untidy garage. He appears to have done a great job for a very reasonable price.

http://www.betaboyz.myzen.co.uk/forum/index.php?topic=4403.msg32460#msg32460 (http://www.betaboyz.myzen.co.uk/forum/index.php?topic=4403.msg32460#msg32460)


Title: Re: Fuel Hose
Post by: Neil-yaj396 on August 21, 2022, 09:27:24 AM
BTW when driving back from the garage that did the work on the brakes for me I was pretty fuel anxious with the warning light on and the gauge needle hovering at bottom. For ease and H&S before removing the tank I pumped it out using my rubber bulb and was surprised to get out nearly 8 litres....


Title: Re: Fuel Hose
Post by: squiglyzigly on November 28, 2022, 07:56:39 PM
This fuel hose conundrum is confusing me more than it should. Since building my Berlina I have now replaced the fuel hose twice. The first change was instigated by visible cracking at the end when the hose was removed for carb maintenance. I decided I didn’t like the idea of the cotton over braid because it hid what is going on underneath.
Today the R9 hose I used to replace the braided hose was replaced again after little over a year of service because it was cracking.


Title: Re: Fuel Hose
Post by: squiglyzigly on November 28, 2022, 08:03:14 PM
After fitting the new R9 of a different make I cut open the 1 year old hose.
It would appear the inner liner was of sufficient quality to deal with e5 shell/esso petrol and the worrying external cracks where because the outer layer was moulded from a lesser quality material.
Annoyingly I don’t know where I purchased the previous hoses, so I am free to make the same purchasing mistake again.

Frustrating to say the least.
Ian


Title: Re: Fuel Hose
Post by: peteracs on November 28, 2022, 08:30:25 PM
Hi Ian

I think the answer is to buy branded hoses from a known reputable manufacturer, not unbranded. There are also reports online of old R6 hoses being relabelled etc.

I bought Cohline R9 for the Spider

https://www.glencoeltd.co.uk/cohline-2240-r9-specification-rubber-fuel-injection-hose-8mm-push-on-e85-compatible-2267/ (https://www.glencoeltd.co.uk/cohline-2240-r9-specification-rubber-fuel-injection-hose-8mm-push-on-e85-compatible-2267/)

Peter


Title: Re: Fuel Hose
Post by: SanRemo78 on November 28, 2022, 08:39:51 PM
Plus one for buying from a reputable supplier and getting a hose that is fully compliant with todays fuels that can eat rubber. I suspect that all the decent hoses on the market will be for fuel injection systems which is probably overkill for Betas with mechanical pumps.

I'd also avoid any hose with an overbraid should be avoided, especially a steel one because you can't see the state of the hose underneath and, when it does fail, the result is a very fine spray or even a mist of fuel vapour. Not ideal.

Guy


Title: Re: Fuel Hose
Post by: squiglyzigly on November 28, 2022, 10:40:50 PM
Hi Ian

I think the answer is to buy branded hoses from a known reputable manufacturer, not unbranded. There are also reports online of old R6 hoses being relabelled etc.

I bought Cohline R9 for the Spider

https://www.glencoeltd.co.uk/cohline-2240-r9-specification-rubber-fuel-injection-hose-8mm-push-on-e85-compatible-2267/ (https://www.glencoeltd.co.uk/cohline-2240-r9-specification-rubber-fuel-injection-hose-8mm-push-on-e85-compatible-2267/)

Peter
Agree completely. And I thought I had purchased a cohline branded hose as pictured.
The hose that you linked is the hose that I have fitted this time.
Fingers crossed 🤞