Lancia Beta Forum
November 06, 2024, 02:57:36 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: 2024 Events Calendar http://www.betaboyz.myzen.co.uk/forum/index.php?board=92.0
Please feel free to add more.
 
   Home   Help Contact Admin Search Calendar Gallery Articles Login Register  
Pages: [1]
  Print  
Author Topic: Torque settings on rear suspension  (Read 712 times)
0 Members and 1 Guest are viewing this topic.
JohnFol
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 388



« on: October 05, 2023, 11:43:00 AM »

Morning all, just refitting rear cross member to chassis and Haynes give 24.5Nm as the torque setting. This feels way too low. (79 spider)
Any advice?



* Torque setting.jpg (800.56 KB, 2933x1625 - viewed 185 times.)
« Last Edit: October 05, 2023, 02:37:53 PM by JohnFol » Logged
WestonE
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 1762


« Reply #1 on: October 05, 2023, 04:52:33 PM »

Go with the Transverse Link settings they are the same size fasteners and even the same thread pitch. Use new P type (Deep) zinc plate Nyloc nuts and thick washers to spread the load.

Eric 
Logged
JohnFol
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 388



« Reply #2 on: October 05, 2023, 06:30:43 PM »

I happened to buy deep nyloc and new bolts for outer ends of transverse arms so I have a few spare.

Although bush issue now resolved, cross member still shows some flex when grabbing wheel (whilst off the ground) and rocking it at 3 & 9 o'clock position.
Can't be sure if this is 1 more issue to solve or typical of the car
Logged
Nigel
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 959



« Reply #3 on: October 05, 2023, 06:50:38 PM »

Hi John,
Remember to have the wheels 'on the ground' when torquing up.

Nigel
Logged

1984 2.0 Carb HPE [ex Aus] Grigio Finanza.
2007 Mazda 6 2.3 [current daily, highly recommended]
The past:
1980 2.0 HPE White in South Africa [hope it survives!]
1976 1.6 Coupe Lancia Blu [PFG 76R] [probably deceased]
oh,and an Uno Turbo 1997 also in SA [stolen,never recovered]
HFStuart
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 1940



« Reply #4 on: October 05, 2023, 07:34:59 PM »

I just had a look in the technical databook and it too says 24.5Nm so that's where Haynes got it from. That has to be a typo - especially as it says to use torque wrench 88091135 which has a range of 29 to 137 Nm
Logged
JohnFol
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 388



« Reply #5 on: October 05, 2023, 07:36:35 PM »

Thanks Stuar

Nigel, Interesting....
Working alone and don't have access to a pit or lift so working under the car whilst on axle stands and clearance is ok. Couldn't imagine getting access behind the road wheel or inboard bushes without it being raised.

 I'm using the infallible Haynes guidance and the suggestion is to effectively load the suspension by jacking under the roll bar, effectively lifting wheel off the floor.

I'm open to a better way...


* PXL_20231003_132647664~3.jpg (1306.13 KB, 3072x1790 - viewed 182 times.)
Logged
Nigel
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 959



« Reply #6 on: October 05, 2023, 10:34:31 PM »

Yes John, that will be sufficient.

This pretty much applies to any metal/rubber bush that will sit 'clamped',
i.e. minimal rubber stress during normal operation.

N.
Logged

1984 2.0 Carb HPE [ex Aus] Grigio Finanza.
2007 Mazda 6 2.3 [current daily, highly recommended]
The past:
1980 2.0 HPE White in South Africa [hope it survives!]
1976 1.6 Coupe Lancia Blu [PFG 76R] [probably deceased]
oh,and an Uno Turbo 1997 also in SA [stolen,never recovered]
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
SMFAds for Free Forums
Valid XHTML 1.0! Valid CSS!