Lancia Beta Forum
September 17, 2019, 08:23:26 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Looking for Lancia Beta Parts
Lots of new items recently added
see: www.lanciabetaparts.co.uk
 
   Home   Help Contact Admin Search Calendar Gallery Articles Login Register  
Pages: [1]
  Print  
Author Topic: Removibg intermediate shaft  (Read 273 times)
0 Members and 1 Guest are viewing this topic.
Per
Full Member
***
Offline Offline

Norway Norway

Posts: 81


« on: June 07, 2019, 10:45:08 PM »

Finally got around to replace the clutch. The manual is a bit unclear when it comes to removing the intermediate shaft from diff to RH drive shaft. Do I undo the three small bolts on the RH bracket plus the four bolts holding the shaft to the diff and pull to the right? Or do I remove the whole big RH bracket? Does the shaft come out of the diff without removing the cover held by four small bolts on the diff?
Logged
Neil-yaj396
Legendary Member
******
Online Online

Posts: 1445


1979 1300 Coupe 1983 2000ie Coupe


« Reply #1 on: June 08, 2019, 08:52:34 AM »

A photo might help?
Logged
rossocorsa
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 2050


« Reply #2 on: June 08, 2019, 09:19:04 AM »

Having done this I should know but can't remember, if you just want to remove the gearbox I think there is no need to remove the mounting though. One thing I would mention is whilst you have access and if it has not been done consider removing the mount and replacing the bearing. It's rarely changed but it does wear, with the shaft in place the inertia of the shaft disguises the wear but once the shaft is out odds on it will feel worn and gritty to rotate.
Logged
Per
Full Member
***
Offline Offline

Norway Norway

Posts: 81


« Reply #3 on: June 08, 2019, 12:14:17 PM »

Ok undid the small bolts on the bracket end. But manual does not say drain diff/box and of course that has to be done if I remove the four bolts holding the intermediate shaft bearing into the diff. If not it will drain that way. So what is the correct procedure?
Logged
HFStuart
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 1638



« Reply #4 on: June 08, 2019, 05:25:34 PM »

The shaft fits on to a small stub shaft that sticks out of the diff. There's a splined sleeve on the inboard end of the intermediate shaft you should be able to see. There's no need to remove the four bolts at the diff. The bearing in the housing is held in place with a circlip. remove the circlip and the shaft should tap out of the housing complete with bearing. If not support the engine and remove the housing from the block together with the driveshaft. There's a circlip at the sline end too (I think...) so the first tap to get it moving might need to be a firm one.
Logged
rossocorsa
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 2050


« Reply #5 on: June 09, 2019, 07:55:55 PM »

https://www.amazon.co.uk/photos/share/nR0hoarE7cPyNL0QqNgJFWh89uT89lHxvu3fyu5qFnK

I think gearbox just slides off but I can't remember for sure
« Last Edit: June 09, 2019, 11:38:43 PM by rossocorsa » Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
SMFAds for Free Forums
Valid XHTML 1.0! Valid CSS!