Lancia Beta Forum
December 10, 2024, 04:16:22 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: 2024 Events Calendar http://www.betaboyz.myzen.co.uk/forum/index.php?board=92.0
Please feel free to add more.
 
   Home   Help Contact Admin Search Calendar Gallery Articles Login Register  
Pages: [1]
  Print  
Author Topic: Stalling after idling for ~1 minute  (Read 3458 times)
0 Members and 1 Guest are viewing this topic.
JohnFol
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 389



« on: December 01, 2020, 12:09:46 PM »

Morning all, just need a bit of advice as I hear tinkering with a carb probably does more harm than good.

Needed to leave car idling yesterday for the first time since owning it. Fired fine from cold and left it whilst moving another car. After ~1 minute the revs gradually dropped and engine cut out. Not sure if this would relate to auto choke not doing it's job or, having read through a posts here, if there is an idle circuit that needs attention.

I think the fuel supply is good as electric pump now fitted with new filter. Only other insights I have are the carb has been previously been rebuilt (many years back) during it's life so has had some professional attention in 40 years, and the filter I replaced was deteriorated so I can't rule out some particles getting past.

There is a Weber specialist just the other side of Reading so not against getting it rebuilt with new gaskets, jets etc. Not sure that sets the carb up for the car though as I would assume that can only be done on the car.

So, do I bite the bullet and get a refurb, or does this sound like a "look at this known issue and I'm 90% sure it'll help" type problem?
Logged
peteracs
Administrator
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 4034


Peter Stokes


« Reply #1 on: December 01, 2020, 02:15:50 PM »

Hi John

I would think a refurb may help. It could be idle jet partially blocked or spindle wear? Check spindle wear by spraying carb cleaner next to exterior of spindle And check for rising revs. Also try adjusting idle screw.

Peter
Logged

Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600
JohnFol
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 389



« Reply #2 on: December 01, 2020, 02:36:02 PM »

will do
Logged
capriblu
Sr. Member
****
Offline Offline

United Kingdom United Kingdom

Posts: 166



« Reply #3 on: December 01, 2020, 09:46:49 PM »

I would check choke set-up and rule this out first. Car wont be warmed through after a minute.  After it stalled did you try restarting ?   Did it restart OK and idle with the help of a slight touch of the throttle ?
Logged

!980 2.0 Coupe - Owned since 1990
mtulloch
Sr. Member
****
Offline Offline

Posts: 177



« Reply #4 on: December 02, 2020, 10:42:11 AM »

I agree with Capriblu above. It sounds like the choke needs adjusted to me.
Logged
JohnFol
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 389



« Reply #5 on: December 02, 2020, 02:35:08 PM »

Thanks for the pointers. Just checked Haynes for some guidance on adjustments and found the autochoke is only semi-auto.

I think I need to try the foot to the floor approach to rule out "user error" before tinkering


* AutoChoke.jpg (978.96 KB, 2699x1832 - viewed 572 times.)
Logged
WestonTB
Sr. Member
****
Offline Offline

Posts: 107


« Reply #6 on: December 04, 2020, 11:56:34 PM »

Should be pretty simple, there does always seem to be a bit of a 'gap' (particularly in winter) when warming from choke screw to throttle screw, it may just be a case of tightening the choke screw slightly.

Haynes do a specific manual for the DATR carbs etc and it's hard to beat.  Get a good new gasket set if needs be with all the diaphragms, manually blow out the jets, of course re-fitting in the correct order! and set all the various adjustments to exactly as the Haynes manual and all should be good.

Taking the carb off and setting it up is fairly straightforward and will probably yield better results than a 'specialist'

Good luck & don't overtighten anything!   
Logged
Neil-yaj396
Legendary Member
******
Offline Offline

Posts: 1949


1979 1300 Coupe


« Reply #7 on: December 05, 2020, 01:39:54 PM »

My first 1300 was pre facelift and had a hand throttle (possibly where the manual choke was on the series 1?). Idle was correctly set at sub 1000 rpm when warm. I had to use the hand throttle for several minutes after the choke dropped off in queueing traffic until it picked up. My current Coupe had the idle set higher to avoid this. Not ideal but it works....
Logged
betabuoy
Hero Member
*****
Offline Offline

United Kingdom United Kingdom

Posts: 325



« Reply #8 on: December 05, 2020, 06:29:04 PM »

My first 1300 was pre facelift and had a hand throttle (possibly where the manual choke was on the series 1?). Idle was correctly set at sub 1000 rpm when warm. I had to use the hand throttle for several minutes after the choke dropped off in queueing traffic until it picked up. My current Coupe had the idle set higher to avoid this. Not ideal but it works....
Oooh, hand throttle Neil? Now you’re talking. Just like our Austin 7!
Logged

1979 Beta Coupe S2FL (1st registered May 1983!)
1967 Morris Minor Traveller
1925 Austin 7 Chummy
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
SMFAds for Free Forums
Valid XHTML 1.0! Valid CSS!