Lancia Beta Forum
March 19, 2024, 03:28:24 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: NEC Restoration Show 22nd-24th March 2024
http://www.betaboyz.myzen.co.uk/forum/index.php?topic=5015.msg36852#msg36852
 
   Home   Help Contact Admin Search Calendar Gallery Articles Login Register  
Pages: [1]
  Print  
Author Topic: Dreaded California smog check  (Read 3406 times)
0 Members and 1 Guest are viewing this topic.
mwredit
Full Member
***
Offline Offline

United States United States

Posts: 80



« on: February 16, 2017, 10:54:06 PM »

Took the HPE to get it smogged this morning.  Well, to my disappointment, it failed due to high CO readings (measured 2.75, Max is 1.46, normal .17).  Everything else was low, like the NOx was below average and the HC was slightly above average.  It seems like the carb is running too rich.  The smog guy said to junk the car (I DONT think so, it's rust free!) and didnt seem too knowledgeable about carbs.  It has a 32 DATRA 12 Weber.  I rebuilt this carb a few months back with a new carb kit and float.  Perhaps the float level is too high?  If it had a power valve, I would suspect that.  I cant imagine it being more than the float setting.  It has been spatting at the mid revs once in a while, the few times I've been driving it.  This car passed smog two years ago and everything passed then.

Thoughts?

Thanks,
Mike
Logged

Mike R.

1968 Mercury Cougar XR7
1961 MG Midget
1974 Ford Mustang II Ghia
1977 Lancia Beta HPE
dougdee123
Full Member
***
Offline Offline

United Kingdom United Kingdom

Posts: 94



« Reply #1 on: February 17, 2017, 10:35:12 AM »

Hi ,

The float level is really not the issue. All that does is stop the the float chamber overfilling.

What you need is someone to adjust the mixture.

http://www.lancisti.net/forum/content.php?2-DMTR-DATR-DATRA-carb-adjustment-guide may help.

Doug
Logged
capriblu
Sr. Member
****
Offline Offline

United Kingdom United Kingdom

Posts: 165



« Reply #2 on: February 17, 2017, 12:35:42 PM »

As first step -  Take the car for a good old "Italian Tune-Up".  Then adjust the idle mixture via the screw (on rear base of carb body on opposite side to throttle linkage/choke).  Turn slowly in (clockwise) until revs just start to drop or roughness in tickover starts to be felt. Then slowly turn out (anti-clockwise) just enough for smooth tickover to return.   Retest CO.   If this yields the improvement needed for test then open out a little more (2/3 a turn).   
Logged

!980 2.0 Coupe - Owned since 1990
mangocrazy
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 1346


Graham Stewart


« Reply #3 on: February 17, 2017, 02:46:01 PM »

What engine revs is the smog test performed at? If it's at idle, then I'd echo what capriblu says. If the test is performed off idle, then you may need to change one or other of the jets. A bad person would run it lean to get through the test, then put it back to 'normal' afterwards. I couldn't possibly condone an action like that, of course...  Grin
Logged

1980 Lancia Beta Spider 2000 (S2FL)
2002 VW Transporter T4
2017 KTM Duke 690R
2008 Aprilia SL1000 Falco
1992 Ducati 888 SP3
1988 Honda VFR750F
1980 Yamaha RD350LC
mwredit
Full Member
***
Offline Offline

United States United States

Posts: 80



« Reply #4 on: February 17, 2017, 05:53:51 PM »

That's what I was told by Mark Allison, a local Fiat guy, to use a larger primary air jet and a smaller primary low speed jet.  Apparently, California tightens up on their requirements every 6 months, so it makes it harder and harder to pass.  Mark told me that my CO readings looked normal for my car.  Here's the readings I got yesterday-

                         HC                                       CO                                     NOx

                MAX    AVE   MEAS                MAX   AVE   MEAS                MAX    AVE   MEAS
15mph       232       40       59                  1.46     .17     2.75              1434    520     344
25mph       200       31       49                  1.26     .15     2.58              1294    452     291

This was done at around 2100-2500 rpm.

Looks like I'm looking at jets now.
Logged

Mike R.

1968 Mercury Cougar XR7
1961 MG Midget
1974 Ford Mustang II Ghia
1977 Lancia Beta HPE
mwredit
Full Member
***
Offline Offline

United States United States

Posts: 80



« Reply #5 on: June 01, 2017, 12:56:47 AM »

To make a long story short, my HPE finally passed Calif smog last week.  The secret is that I had to change out the idle air jet for the primary side to a bigger size for the test.  I used one that was drilled out.  This brought the CO% down.  However, the air injector rail that attaches to the head was 3/4 plugged, which had added to the problem.
Logged

Mike R.

1968 Mercury Cougar XR7
1961 MG Midget
1974 Ford Mustang II Ghia
1977 Lancia Beta HPE
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
SMFAds for Free Forums
Valid XHTML 1.0! Valid CSS!