Lancia Beta Forum
November 12, 2024, 08:30:31 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Looking for Lancia Beta parts: www.lanciabetaparts.co.uk
 
   Home   Help Contact Admin Search Calendar Gallery Articles Login Register  
Pages: [1]
  Print  
Author Topic: Rear caliper pistons  (Read 3683 times)
0 Members and 1 Guest are viewing this topic.
smithymc
Hero Member
*****
Offline Offline

Posts: 681


« on: July 07, 2012, 01:16:06 PM »

Am on the rear brakes now. The Haynes manual calmly says 'screw piston clockwise into caliper' to gain clearance for new pads.

Any tips on how, what with and whether you need a gorilla to hold caliper and turn piston at same time?

Much bad language and skin loss in past half hour.

Thanks for any help.

Mark
Logged
MattNoVAT
Administrator
Legendary Member
******
Offline Offline

France France

Posts: 1830



« Reply #1 on: July 07, 2012, 02:00:06 PM »

Sometimes you need to screw them in and apply quite a bit of force so that the thread picks up and the piston starts receding, I've even had to tap gently with a hammer on the head of the piston on rare occasions because the piston has come out too far.
Logged

1981 2000 Coupe S2/FL
1976 1600 Coupe S1
2007 Ypsilon 1.3 Bi-Colori
HFStuart
Legendary Member
******
Offline Offline

United Kingdom United Kingdom

Posts: 1940



« Reply #2 on: July 07, 2012, 10:51:23 PM »

A piece of 6mm keysteel is just about perfect IIRC to turn the piston. As Matt says sometimes you need a bit of force too.
Logged
MattNoVAT
Administrator
Legendary Member
******
Offline Offline

France France

Posts: 1830



« Reply #3 on: July 08, 2012, 07:15:41 AM »

I use a tool that was originally meant for bolts that secured the anti-tilt plates for AS400 expansion racks ( computer kit )

But there are universal square block sockets that are about £7 from Halfrauds that make life easier.
Logged

1981 2000 Coupe S2/FL
1976 1600 Coupe S1
2007 Ypsilon 1.3 Bi-Colori
Neil-yaj396
Legendary Member
******
Offline Offline

Posts: 1938


1979 1300 Coupe


« Reply #4 on: July 08, 2012, 08:25:40 AM »

If the piston won't respond to the suggestions above it's time for a rebuild anyway as the handbrake won't be responsive.
Logged
smithymc
Hero Member
*****
Offline Offline

Posts: 681


« Reply #5 on: July 09, 2012, 09:49:49 AM »

Thanks all.  After some rummaging I found an old trim pry-bar with a square shank that worked a treat - once they started to move it was easy. It was even pretty good for prying the caliper to get the wedges in.

In doing the job, I found some quite corroded brake pipes up around the fuel tank ( and some more nasty fuel pipes). Are the braided brake kits a good choice and easier to work with than metal pipes in the confined space? Any thoughts?

Thanks.

Mark
Logged
Neil-yaj396
Legendary Member
******
Offline Offline

Posts: 1938


1979 1300 Coupe


« Reply #6 on: July 10, 2012, 07:21:46 AM »

The braided kits only replace the flexible (rubber) pipes. You will need a full pipe kit or to get the new sections you need made up.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines
SMFAds for Free Forums
Valid XHTML 1.0! Valid CSS!